d&b audiotechnik Yi10P Point-Source Loudspeaker

Point-source loudspeaker with dual 8″ drivers and rotatable CD horn—for fixed installation


The d&b audiotechnik Yi10P is a dual 8″, 400/1,600W (RMS/peak) point-source loudspeaker with a bass reflex cabinet and rotatable high-frequency CD horn—fixed installation version.

The d&b audiotechnik Y-series is designed to offer flexible and highly configurable systems for use in even the most challenging sound reinforcement applications. The Yi10P loudspeakers can be used for small- to medium-scale sound systems in standalone or distributed point-source solutions. It can also figure into a medium-sized line array setup. The Yi10P’s mounting options are suited fixed installation.

Featuring the same internal components, but with wider dispersion characteristics than the Yi7P, the compact, 2-way passive Yi10P loudspeaker features two 8” drivers in a dipole arrangement with a 1.4” compression driver mounted onto a rotatable constant directivity (CD) horn. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These point source, high-performance cabinets offer 110° horizontal directivity controlled down to 500Hz, matched with a vertical dispersion of 40°. The horn can be rotated by 90° to enable horizontal orientation.

d&b audiotechnik Yi10P—At a Glance

  • High performance 2-way passive point source loudspeaker
  • Cabinet fitted for fixed installation
  • 2x 8″ drives
  • 4″ HF compression driver mounted in a CD horn
  • Dispersion 110° x 40°
  • 136dB SPL max.

d&b audiotechnik Yi10P—Parsing the Details

The Yi10P is a passive point-source loudspeaker. It features a dipolar speaker arrangement with two 8″ drivers centered around a 1.4″ HF compression driver mounted on a CD horn with 110° x 40° dispersion characteristics. A rotatable horn enables deployment in either orientation, while an innovative bass-reflex and port design gives an increased LF performance. The high performance omnidirectional B6 and Bi6-SUB feature a single 18″ long excursion driver, intended for ground stacked applications only.

The Yi10P provides a broad variety of deployment possibilities, especially when used as a standalone, full-range system, or combined with other elements from the Y-Series, either ground stacked or flown. The loudspeaker cabinet is constructed from marine plywood and has an impact resistant paint finish while Weather Resistant (WR) and Special Color (SC) versions are available. The Weather Resistant option provides an IP55* rating, and enables operation of loudspeakers in changing ambient conditions.

The top and bottom panels of the cabinets are each equipped with a pair of M10 threaded inserts to connect to different rigging accessories such as the Z5398 YP Horizontal bracket, the Z5399 YP Mounting bracket, the Z5354 E8/E12 Flying adapter or the Z5020/25 Flying adapter 02/03.

*The IP Code or International Protection Rating, sometimes also interpreted as Ingress Protection Rating. IP55: Protected from limited dust ingress. Protected from low-pressure water jets from any direction. 

HFA circuit

In HFA mode (High Frequency Attenuation), the HF response of the system is rolled off. HFA provides a natural, balanced frequency response when a unit is placed close to listeners in near field or delay use. High Frequency Attenuation begins gradually at 1kHz, dropping by approximately 3dB at 10kHz. This roll-off mimics the decline in frequency response experienced when listening to a system from a distance in a typically reverberant room or auditorium.

CPL function 

The CPL (Coupling) function compensates for coupling effects between the cabinet and close boundary surfaces or when the cabinet is used as a stage monitor. CPL begins gradually around 1kHz, with the maximum attenuation below 400Hz. To achieve a balanced frequency response, the CPL function can be set to dB attenuation values between 0 and –9. Positive CPL values create an adjustable low frequency boost (0 to +5dB) and can be set when the system is used in full range mode without subwoofers

Recommended d&b audiotechnik amplifiers 

The d&b D80 amplifier is recommended to drive the Yi10P. The d&b D20, 10D, 30D and D6 can also be used.

Yi10P applications

  • Theater and opera
  • Live performance venues
  • Nightclubs and bars
  • Houses of worship
  • Other applications for fixed installation

Architectural specifications for detailed project planning

If you require architectural specifications for a d&b system or a specific d&b Series, you can find the most important technical specifications ready for download on the d&b audiotechnik website. 

For more information or assistance configuring a system with d&b audiotechnik Yi10P point-source loudspeakers, call or chat online with your Parsons Audio professional today.  


d&b audiotechnik Yi10P Specifications:

System Data

  • Frequency response (-5dB standard): 59Hz – 18kHz
  • Frequency response (-5dB CUT mode): 118Hz – 18kHz

Max. sound pressure1

  • D6/10D: 131dB
  • D12/D20/30D: 134dB
  • D80: 136dB
  • Cabinets per amplifier channel: 2

1: 1m, free field, SPL max peak test signal: pink noise with crest factor 4 

Loudspeaker data

  • Configuration: High-performance 2-way passive point source loudspeaker
  • Nominal impedance: 8 ohm
  • Power handling capacity (RMS/peak 10 ms): 400/1600W
  • Nominal dispersion angle (h x v): 110° x 40°


  • 2x 8″ driver with neodymium magnet
  • 4″ exit compression driver
  • passive crossover network


  • 2 x NLT4 F/M
  • optional 2 x NL4 or 2 x EP5


  • H: 22-13/16″ (580 mm)
  • W: 10″ (257 mm)
  • D: 13-7/16″ (341 mm)


  • 40 lb. (18 kg)

Additional information

Weight 40 lbs
Dimensions 14 × 10 × 23 in