Quested V3110

1000W Active 3-Way Reference Monitor

Description

INTRODUCING THE Quested V3110

Designed for use in near to midfield applications, the V3110 is our most powerful self-powered monitor and, because of its 1000 watts of class AB and class D amplification, it is one of the most powerful in its class. The three-way design of the V3110 and the utilization of the soft dome mid and high-frequency drivers along with the custom 10″ low frequency driver mean that the V3110 truly can deliver for the most demanding of material with a flat response down to 30Hz.

The successor to the VS3208, a favorite with the dance and remix fraternity the V3110 has been able to improve on the low-end performance whilst maintaining that precision recognized in the VS3208. Producing a very linear response along with the capability of high SPL the V3110 is also a favorite of the scoring community. Delivering a dynamic and very natural sound stage with response all the way down to the lower register of a church organ the V3110 is the flagship product of the powered monitors from Quested.

TECHNICAL SPECIFICATION

Size: 380 x 600 x 360mm (w x h x d)

Weight: 39kg / 86lb

Driver: Low Frequency 1 x 250mm(10″)

Mid: 1 x 75mm (3”) soft dome

High Frequency: soft dome 1 x 28mm (1 1/8″)

Frequency Response: 34Hz – 20kHz ±2dB / 30Hz – 22kHz -6 dB

Maximum SPL: 115.5 dB continuous pink noise @ 1m Leq 1 minute. 121.5 dB continuous pink noise per pair @ 1m Leq 1 minute

INPUT

Connector: XLR3 type-Female

Impedance: 10k Electronically balanced with RF filters

Wiring: Pin 1 ground, Pin 2 hot, Pin 3 cold

Sensitivity: Rear mounted 10 position rotary switch calibrated in 2dB steps

Minimum sensitivity +4dBu for 100dB SPL @ 1m

Maximum sensitivity -14dBu for 100 dB SPL @ 1m

FILTERS

Subsonic: -3dB @ 14Hz, 24dB/oct

Crossover Points: 650Hz, 2k5H, 24dB/oct.

User LF EQ: 4 position rear mounted selector to select FLAT for normal use. -9dB and -3dB for cut below 100Hz, +1dB for lift above 80Hz.

User MF EQ 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 650Hz to 2k5Hz.

User HF EQ 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 2k5Hz to 40kHz.

POWER AMPLIFIER

LF output power: > 700W rms continuous (Note 1)

Mid Output: > 150W rms continuous (Note 1)

HF output power: > 150W rms continuous (Note 1)

THD: < 0.03% at levels up to 1dB below clip, 20Hz – 20kHz. typ 0.005% @ 20W rms 1kHz.

Hum + Noise > -100dB referred to clip

Note 1: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier rear panel and ambient temperatures is <30 o C

INDICATION

Power on: Front mounted LED (flashing blue) indicates power applied and warm-up cycle.

Optimum Performance: Front-mounted LED lights constant blue.

Overload: Front mounted LED flashes red 0.5dB below signal clip.

Thermal Protection: Front mounted LED turns red, the signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when amplifier temperature drops by 20 o C.

POWER REQUIREMENTS

Voltage: Set by internal plugs: nominal 115V or 230V @ 50-60Hz AC.

230V setting: Min 160V (restricted output power): Max 263V

115V setting: Min 80V (restricted output power): Max 132V

CONSUMPTION

Quiescent 72W, typical use 110W.

Note 0dBu = 775mV into open circuit.

This product is built to conform to the requirements for CE marking.

Reviews

There are no reviews yet.

Be the first to review “Quested V3110”

Your email address will not be published. Required fields are marked *